The Alexander Manufacturing Company in Rochester, Minnesota, assembles and tests electronic components used in smartphones. Consider the following data regarding component T24 (amounts are per unit):

Direct materials cost \( 81.00

Direct labor cost 21.00

Activity-based costs allocated ?

Total manufacturing product cost ?

The activities required to build the component follow:

Activity

Allocation Base

Cost Allocated to Each Unit

Start Station

Number of raw component chassis

3 X \)1.50 = \(4.50

Dip Insertion

Number of dip insertions

? X 0.50 = 14.50

Manual Insertion

Number of manual insertions

13 X 0.40 = ?

Wave solder

Number of components solders

3 X 1.50 = 4.50

Backload

Number of backload insertions

7 X ? = 2.80

Test

Number of testing hours

0.39 60.0 = ?

Defect analysis

Number of defect analysis hours

0.10 X ? = 4.00

Total activity-based costs

\) ?

Requirements

2. Why might managers favor this ABC system instead of Alexander’s older system, which allocated all manufacturing overhead costs on the basis of direct labor hours?

Short Answer

Expert verified

The activity-based costing is preferred over traditional methods due to reasonable allocation based on different activities associated with different products.

Step by step solution

01

Step-by-Step-SolutionStep 1: Activity-based costing system

Activity-based costing system is a procedure for allocating costs based on different tasks, operations, or procedures. Under activity-based costing, the overhead costs are segregated between different activities and then the different activities costs are allocated to different products or services.

02

Why activity based costing is preferred over traditional costing

Under traditional costing, the overhead costs are allocated based on a single allocation base. That allocation base may or may not be relevant to all products. So, the cost ascertained under the traditional method may be relevant for some products but may not be relevant or fair for other products.

Under activity-based costing, the overheads are allocated based on the activities associated with different products. In this way, all products are charged for the relevant activities performed for that product. So, the cost ascertained for different products under this system is relevant and fair for all products.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

Question:Refer to Exercise E19-26. Western desires a 20% target net profit after covering all costs. Considering the total costs assigned to the Halbert engagement in Exercise E19-26, what would Western have to charge the customer to achieve that net profit? Roundto two decimal places.

Harcourt Pharmaceuticals manufactures an over-the-counter allergy medication. The company sells both large commercial containers of 1,000 capsules to health care facilities and travel packs of 20 capsules to shops in airports, train stations, and hotels. The following information has been developed to determine if an activity-based costing system would be beneficial:

Activity Estimated Estimated Quantity

Indirect Cost Allocation Base of Allocation Base

Materials handling \( 96,000 Number of kilos 24,000 kilos

Packaging 210,000 Number of machine hours 3,000 hours

Quality assurance 114,000 Number of samples 1,900 samples

Total indirect costs \) 420,000

Other production information includes the following:

Commercial Containers Travel Packs

Units produced 2,800 containers 51,000 packs

Weight in kilos 9,800 5,100

Machine hours 1,960 510

Number of samples 560 765

Requirements

1. Harcourt’s original single plantwide overhead allocation rate system allocated indirect costs to products at $140.00 per machine hour. Compute the total indirect costs allocated to the commercial containers and to the travel packs under the original system. Then compute the indirect cost per unit for each product. Round to two decimal places.

Loiselle manufactures high-quality speakers. Suppose Loiselle is considering spending the following amounts on a new quality program:

___________________________________________________________________

Additional 20 minutes of testing for each speaker \( 625,000

Negotiating and training suppliers to obtain higher-quality

materials and on-time delivery 430,000

Redesigning the speakers to make them easier to manufacture 1,250,000

Loiselle expects this quality program to save costs as follows:

__________________________________________________

Reduce warranty repair costs \) 275,000

Avoid inspection of raw materials 580,000

Avoid rework because of fewer defective units 825,000_

It also expects this program to avoid lost profits from the following:

___________________________________________________

Lost profits due to disappointed customers $ 920,000

Lost production time due to rework 278,000

Requirements

1. Classify each of these costs into one of the four categories of quality costs (prevention, appraisal, internal failure, or external failure).

2. Should Loiselle implement the quality program? Give your reasons.

Martin, Inc. manufactures bookcases and uses an activity-based costing system. Martin’s activity areas and related data follow:

Activity

Budgeted Cost of Activity

Allocation Base

Predetermined Overhead Allocation Rate

Materials handling

\( 230,000

Number of parts

\)1.50

Assembly

3,200,000

Number of assembling direct labor hours

16.00

Finishing

150,000

Number of finished units*

3.00

*Refers to the number of units receiving the finishing activity, not the number of units transferred to Finished Goods Inventory

Martin produced two styles of bookcases in April: the standard bookcase and an unfinished bookcase, which has fewer parts and requires no finishing. The totals for quantities, direct materials costs, and other data follow:

Product

Total Units Produced

Total Direct materials Costs

Total Direct Labor Costs

Total Number of Parts

Total Assembling Direct Labor Hours

Standard bookcase

3,000

\(54,000

\)67,500

9,000

4,500

Unfinished bookcase

3,500

56,000

52,500

7,000

3,500

Requirements

1. Compute the manufacturing product cost per unit of each type of bookcase.

Turbo Champs Corp. uses activity-based costing to account for its motorcycle manufacturing process. Company managers have identified three supporting manufacturing activities: inspection, machine setup, and machine maintenance. The budgeted activity costs for 2018 and their allocation bases are as follows:

Activity Total Budgeted Cost Allocation Base

Inspections \( 5,700 Number of inspections

Machine setup 22,000 Number of setups

Machine maintenance 6,000 Finishing of machine hours

Total \) 33,700

Turbo Champs expects to produce 20 custom-built motorcycles for the year. The motorcycles are expected to require 100 inspections, 40 setups, and 100 machine hours.

Requirements

2. Compute the expected indirect manufacturing cost of each motorcycle.

See all solutions

Recommended explanations on Business Studies Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free