(a) From Box 5-3, estimate the minimum expected coefficient of variation,CV(%)

, for interlaboratory results when the analyte concentration is (i) 1 wt % or (ii) 1 part per trillion.

(b) The coefficient of variation within a laboratory is typically~0.5-0.7of the between-laboratory variation. If your class analyzes an unknown containing10wt%NH3, what is the minimum expected coefficient of variation for the class?

Short Answer

Expert verified

(a) a-i) The required 1 wt% is CV%is4%

(b) The minimum expected coefficient of vatiation for the class is CV%is1.4%

Step by step solution

01

Defition of coefficient of variation

  • The standard deviation to mean ratio is known as the coefficient of variation (CV).
  • The larger the dispersion around the mean, the higher the coefficient of variation. In most cases, it's given as a percentage.
02

Determine the coefficient of variance and cv%

(a)

Solve for the least predicted cofficients of variance, cv percent, in this issue (both parts a and b).

It has provided the following for the first component (a):

concentration of analyte (i) 1 wt\% and (ii) 1 part per trillion

It can easily solve for the CV percent using the analyte concentration. It can enter the value into the equation as follows:

a-i.)

CV%=21-0.5logC=21-0.5log0.01=22CV%=4%

a-ii.)

CV%=21-0.5logC=21-0.5log1×10-12=22CV%=128%

03

Determine the CV%

(b)

It provided the following for component b:

between-laboratory variance of about 0.5 to 0.7 an unknown containing10wt%NH3

When calculating the CV percent, we just enter the specified values into the algorithm. Then there's:

CV%=0.5×21-0.5logC=0.521-0.5log0.5=0.5×21.5CV%=1.4%

To figure out what the coefficient of variance is. However, we are requested to find the minimum in this problem, and we are given the values ( 0.5 to 0.7 ). As a result, we consider the stated minimum variation (which is 0.5 ).

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

Detection limit. In spectrophotometry, we measure the concentration of an analyte by its absorbance of light. A low-concentration sample was prepared and nine replicate measurements gave absorbances of 0.0047,0.0054,0.0062,0.0060,0.0046,0.0056,0.0052,0.0044, and 0.0058. Nine reagent blanks gave values of 0.0006,0.0012, 0.0022,0.0005,0.0016,0.0008,0.0017,0.0010, and 0.0011.

a) Find the absorbance detection limit with equation 5-3.

b) The calibration curve is a graph of absorbance versus concentration. Absorbance is a dimensionless quantity. The slope of the calibration curve is m=2.24x104M-1Find the concentration detection limit with Equation 5-5.

(c) Find the lower limit of quantitation with Equation 5-6.

State when standard additions and internal standards, instead of a calibration curve, are desirable, and why.

5-28. Ititandard addition. Lead in dry river sediment was extracted with 25wt%HNO3at35°Cfor1h.then1.00mLof filtered extract was mixed with other reagents to bring the total volume to V0=4.60mL.pb(ll)was measured electrochemically with a series of standard additions of 2.50pb(ll).


(a) Volume is not constant, so follow the procedure of Figures 5-5 and 5-6 to find ppmpb(ll)inthe1.00-mL

extract.

(b) Find the standard uncertainty and 95%confidence interval for the x-intercept of the graph. Assuming that uncertainty in intercept is larger than other uncertainties, estimate the uncertainty in ppm pb(ll)inthe1.00-mLextract.

In a murder trial in the 1990 s, the defendant's blood was found at the crime scene. The prosecutor argued that blood was left by the defendant during the crime. The defense argued that police "planted" the defendant's blood from a sample collected later. Blood is normally collected in a vial containing the metal-binding compound EDTA (as an anticoagulant) at a concentration of ~4.5mMafter the vial is filled with blood. At the time of the trial, procedures to measure EDTA in blood were not well established. Even though the amount of EDTA found in the crime-scene blood was orders of magnitude below ~4.5mM

, the jury acquitted the defendant. This trial motivated the development of a new method to measure EDTA in blood.

(a) Precision and accuracy. To measure accuracy and precision of the method, blood was fortified with EDTA to known levels.

Accuracy=100×meanvaluefound-knownvalueknownvaluePrecision=100×standarddeviationmean=coeffcientofvariation

For each of the three spike levels in the table, find the precision and accuracy of the quality control samples.

(b) Detection and quantitation limits. Low concentrations of EDTA near the detection limit gave the following dimensionless instrument readings: 175,104,164,193,131,189,155,133,151, and 176. Ten blanks had a mean reading of 45 - 1 . The slope of the calibration curve is1.75×199M-1. Estimate the signal and concentration detection limits and the lower limit of quantitation for EDTA.

Standard addition graph. Allicin is a ~0.4wt%component in garlic with antimicrobial and possibly anticancer and antioxidant activity. It is unstable and therefore difficult to measure. An assay was developed in which the stable precursor alliin is added to freshly crushed garlic and converted to allicin by the enzyme alliinase found in garlic. Components of the garlic are extracted and measured by chromatography. The chromatogram shows standard additions reported as mg alliin added per gram of garlic. The chromatographic peak is allicin from the conversion of alliin.

(a)The standard addition procedure has a constant total volume. Measure the responses in the figure and prepare a graph to find how much alliin equivalent was in the unspiked garlic. The units of your answer will be mg alliin/g garlic. Find the 95%confidence interval, as well.

(b) Given that2molof alliin are converted to1molof allicin, find the allicin content of garlic (mg allicin/g garlic) including the95%confidence interval.

See all solutions

Recommended explanations on Chemistry Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free