In an experiment analogous to that in Figure 28-3, the sampling constant is found to be \({K_{\rm{s}}} = 20\;{\rm{g}}.\)

(a) What mass of sample is required for a \( \pm 2\% \)sampling standard deviation?

(b) How many samples of the size in part (a) are required to produce \(90\% \)confidence that the mean is known to within\(1.5\% \)?

Short Answer

Expert verified

(a) The mass of the sample for the given standard deviation is\(5\;{\rm{g}}\).

(b) In this case we should use \(7\) samples,\(n = 4.8,8.1,6.4,7.2,6.7\)

Step by step solution

01

Definition of Standard deviation.

  • The standard deviation is a measure of how far something deviates from the mean (for example, spread, dispersion, or spread). A "typical" variation from the mean is represented by the standard deviation.
  • Because it returns to the data set's original units of measurement, it's a common measure of variability.
  • The standard deviation, defined as the square root of the variance, is a statistic that represents the dispersion of a dataset relative to its mean.
02

Determine the mass of the sample

a)

Calculate the mass of sample with the following equation

\(\begin{array}{l}m{R^2} = {K_S}\\m = \frac{{{K_S}}}{{{R^2}}}\\m = \frac{{20\;{\rm{g}}}}{{{2^2}}}\\m = 5\;{\rm{g}}\end{array}\)

Hence, the mass of the sample for the given standard deviation is \(5\;{\rm{g}}\).

03

Calculate the number of samples.

b)

Use the equation 28-7 with \({s_s} = 0.02\) and \(e = 0.015\), the initial value of \(t\) is found on the Pg.72 Table \(4 - 4\) for confidence \(90\% \) :

\(\begin{array}{l}n = \frac{{{t^2}s_s^2}}{{{e^2}}}\\n = \frac{{{{1.645}^2} \times {{0.02}^2}}}{{{{0.015}^2}}}\\n = 4.8\end{array}\)

Next, for \(n = 5\) there are \({4^^\circ }\) of freedom so \(t = 2.132\) which gives the following value of \(n\) :

\(n = \frac{{{t^2}s_s^2}}{{{e^2}}}\)

\(\begin{array}{l}n = \frac{{{{2.132}^2} \times {{0.02}^2}}}{{{{0.015}^2}}}\\n = 8.1\end{array}\)

Then if we use in the same equation the \({7^^\circ }\) of freedom \(t = 1.895\) this would give us the following value of \(n\) :

\(\begin{array}{l}n = \frac{{{t^2}s_s^2}}{{{e^2}}}\\n = \frac{{{{1.895}^2} \times {{0.02}^2}}}{{{{0.015}^2}}}\\n = 6.4\end{array}\)

Then with \(t = 2.015 \to n = 7.2\) and \(t = 1.943 \to n = 6.7\)So, we would use a total of \(7\) samples.

Therefore, in this case we should use \(7\) samples,\(n = 4.8,8.1,6.4,7.2,6.7\)

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

What measures can be taken to decrease the relative supersaturation during a precipitation?

(a) Figure 1-1 shows a peak O3concentration of 13mPain the stratosphere. Figure 1-3 shows a peak concentration of O3 of 39ppbat ground level at one particular location. To compare these concentrations, convertto pressure in. Which concentration is higher? To convert 39ppb to, assume that atmospheric pressure at the surface of the Earth is 1 bar =105Pa. If atmospheric pressure is 1 bar, then a concentration ofis.

(b) The pressure of the atmosphere at 16kmaltitude in the stratosphere is 9.6kPa. The peak pressure O3 ofat this altitude in the stratosphere in Figure 1-1 is 19mPa. Convert the pressure of 19mPa toppb when the atmospheric pressure is 9.6kPa

An unknown sample of Cu2+gave an absorbance of 0.262 in an atomic absorption analysis. Then 1.00 mL of solution containing 100.0 ppm (=g/mL)Cu2+was mixed with 95.0mL of unknown, and the mixture was diluted to 100.0mL in a volumetric flask. The absorbance of the new solution was 0.500.

(a) Denoting the initial, unknown concentration as [Cu2+]i, write an expression for the final concentration,Cu2+f, after dilution. Units of concentration are ppm.

(b) In a similar manner, write the final concentration of added standard Cu2+, designated as [S]f.

(c) Find [Cu2+]i in the unknown.

The relative retention for two compounds in gas chromatography is 1.068 on a column with a plate height of 0.520mm.The retention factor for compound 1 is 5.16.

(a) Find the retention factor for compound 2.

(b) What length of column will separate the compounds with a resolution of 1.50 ?

(c) The retention time for air (tm) is 2.00 min. If the number of plates is the same for both compounds, Findtrandw12for each peak.

(d) If the volume ratio of stationary phase to mobile phase is 0.30,Find the partition coefficient for compound 1.

Effect of concentration in the titration of weak acid with strong base.Use your spreadsheet from Problem 11-66 to prepare a family of titration curves for pKa = 6, with the following combinations of concentrations: (a) Ca = 20 mM, Cb = 100 mM; (b) Ca = 2 mM, Cb = 10 mM; (c) Ca = 0.2 mM, Cb = 1 mM.

See all solutions

Recommended explanations on Chemistry Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free