Problem 1.36. In the course of pumping up a bicycle tire, a liter of air at atmospheric pressure is compressed adiabatically to a pressure of 7 atm. (Air is mostly diatomic nitrogen and oxygen.)

(a) What is the final volume of this air after compression?

(b) How much work is done in compressing the air?

(c) If the temperature of the air is initially300K , what is the temperature after compression?

Short Answer

Expert verified

Part (a) The final volume of the air after compression is Vf=2.49×10-4 m3.

Part (b) Work done on the air is W=188.44 J.

Part (c) The final temperature after compression is Tf=523.17 K.

Step by step solution

01

Part a. Step 1. Given information.

A liter of air at atmospheric pressure is compressed adiabatically to a pressure of 7 atm.

Air is mostly diatomic.

02

Part a. Step 2. Explanation.

Expression for the adiabatic process is

PVγ=constant

Here Pis the pressure of air, Vis the volume of the air, and γis the adiabatic constant.

In the initial and final case equation (1) can be written as

PiViγ=PfVfγ

Equation (2) can be simplified as

Vfγ=PfVfγPf

Multiply 1γon both sides of equation (3)

Vf=PiPf1γVi

Vf=1757×1Vf=0.249 L=2.49×10-4 m3Vf=2.49×10-4 m3

Hence, the required final volume is 2.49×10-4 m3.

03

Part b. Step 1. Given information.

1 liter of air is compressed adiabatically to a pressure of 7 atm. The initial volume of air is1×103 m3 and the final volume is 2.49×104 m3.

04

Part b. Step 2. Explanation.

Expression for work done on the system is

W=vivfPdV …… (1)

Here Pis the pressure, Vi and Vfare initial volume, and final volume.

Expression for the adiabatic process is

role="math" localid="1651473925139" PVγ=const …… (2)

Here Pis the pressure of air,V is the volume of the air, andγ is the adiabatic constant.

Equation (2) can be written as

TVγ1=const

Tf=1×1032.49×10425×300

P=cVγ …… (3)

Substitute cVγfor Pin equation (1)

W=c1×1032.49×104VγdV …… (4)

Solving equation (4) forW

W=cVγ+1γ+11×1032.49×104 …… (5)

Substitute 75for γin equation (5)

W=29.48.c …… (6)

At V=1 liter=1×103 m3and role="math" localid="1651475635356" 101325 Pafor Pin equation (2)

PVγ=c1.013×105×1×10375=cc=6.393 Pa.

Substitute for in equation (6)

W=29.48×6.393W=188.44 J

Hence, work done on the air is W=188.44 J.

05

Part c. Step 1. Given information.

The initial temperature is Ti=300 K.

The initial volume isVi=1×103 m3 and the final volume is Vf=2.49×104 m3.

06

Part c. Step 2. Explanation.

Expression for adiabatic compression is

VTf2=const …… (1)

Here, Vis the volume of the air, T is temperature andf is the degree of freedom.

Equation (1) can be written for the initial and final cases as

ViTif2=VfTff2Tff2=ViVf2fTi

…… (3)

Substitute 5 for f, 1×103m3for Vi, 2.49×104 m3for Vfon equation (3)

Tf=1×1032.49×10425×300Tf=523.17 K

Hence, the final temperature after compression is Tf=523.17 K.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

In analogy with the thermal conductivity, derive an approximate formula for the viscosity of an ideal gas in terms of its density, mean free path, and average thermal speed. Show explicitly that the viscosity is independent of pressure and proportional to the square root of the temperature. Evaluate your formula numerically for air at room temperature and compare to the experimental value quoted in the text.

Calculate the total thermal energy in a gram of lead at room temperature, assuming that none of the degrees of freedom are "frozen out" (this happens to be a good assumption in this case).

Put a few spoonfuls of water into a bottle with a tight lid. Make sure everything is at room temperature, measuring the temperature of the water with a thermometer to make sure. Now close the bottle and shake it as hard as you can for several minutes. When you're exhausted and ready to drop, shake it for several minutes more. Then measure the temperature again. Make a rough calculation of the expected temperature change, and compare.


An ideal gas is made to undergo the cyclic process shown in the given figure. For each of the steps A, B, and C, determine whether each of the following is positive, negative, or zero: (a) the work done on the gas; (b) the change in the energy content of the gas; (c) the heat added to the gas.

Then determine the sign of each of these three quantities for the whole cycle. What does this process accomplish?

Measured heat capacities of solids and liquids are almost always at constant pressure, not constant volume. To see why, estimate the pressure needed to keep Vfixed as Tincreases, as follows.

(a) First imagine slightly increasing the temperature of a material at constant pressure. Write the change in volume,dV1, in terms of dTand the thermal expansion coefficient βintroduced in Problem 1.7.

(b) Now imagine slightly compressing the material, holding its temperature fixed. Write the change in volume for this process, dV2, in terms of dPand the isothermal compressibility κT, defined as

κT1VVPT

(c) Finally, imagine that you compress the material just enough in part (b) to offset the expansion in part (a). Then the ratio of dPtodTis equal to (P/T)V, since there is no net change in volume. Express this partial derivative in terms of βandκT. Then express it more abstractly in terms of the partial derivatives used to define βandκT. For the second expression you should obtain

PTV=(V/T)P(V/P)T

This result is actually a purely mathematical relation, true for any three quantities that are related in such a way that any two determine the third.

(d) Compute β,κT,and(P/T)Vfor an ideal gas, and check that the three expressions satisfy the identity you found in part (c).

(e) For water at 25C,β=2.57×104K1andκT=4.52×1010Pa1. Suppose you increase the temperature of some water from 20Cto30C. How much pressure must you apply to prevent it from expanding? Repeat the calculation for mercury, for which (at25C)β=1.81×104K1andκT=4.04×1011Pa1

Given the choice, would you rather measure the heat capacities of these substances at constant vor at constant p?

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free