Your 200 g cup of tea is boiling-hot. About how much ice should you add to bring it down to a comfortable sipping temperature of 65°C? (Assume that the ice is initially 65°C. The specific heat capacity of ice isrole="math" localid="1650146844935" 0.5cal/g°C.

Short Answer

Expert verified

Short Answer:

m=45.9g

Step by step solution

01

Given Information:

Mass of cup = 200 g

Initial Temp = 65 oC

02

Step 1:

We have a 200 gram cup of boiling tea that we'd want to chill down to 65°C before we drink it, by putting a mass m of ice (initially at -15 oC ) into the tea Given that the specific heat cal·g-1·K-1. Assume that the tea have the same heat capacity as pure water 1 cal·g-1·K-1, the tea must decrease by 35Kso it must give up an amount of heat:

Qneater=mcΔT

Qtea=200×1×(35)-7000cal

This heat goes into, first, heating the ice by 15 degrees to its melting point, then melting it, then heating the resulting water to 65 oC.

03

Step 2:

For the first step, the required heat raises the temperature of ice to its melting point is:

Q1=mcΔT

where m is the mass of the ice, c is the specific heat of ice 0.5cal·g-1·K-1, andT is the temperature difference between the initial temperature of ice and the melting point, so

role="math" localid="1650148419303" Q1=m×0.5×(0-(-15))=7.5mcal

In the second step, the amount of heat required to melt the ice is:

Q2=m·L

where L is the latent heat, and it's 80cal/gfor melting ice, so:

Q2=m·80=80mcal

- In the third step, the amount of heat lost by the tea to make the resulting water temperature at 65°Cis,

Q3=mcΔT

where m is the mass of the melted ice (water), c is the specific heat of water 1cal·g-1·K-1and Tis the temperature difference between the initial temperature of melted ice and the final temperature of the mixture at 65°C, so:

Q3=m×1×(65-0)

=65 mcal

04

Step 3:

The sum of these three heats is equal to the heat lost by the tea is:

Qcas=Q1+Q2+Q3

=7.5mcal+80mcal+65mcal

=152.5mcal

Therefore:

m=45.9g

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

Home owners and builders discuss thermal conductivities in terms of the value (Rfor resistance) of a material, defined as the thickness divided by the thermal conductivity:

RΔxkt

(a) Calculate the Rvalue of a 1/8-inch(3.2mm) piece of plate glass, and then of a 1mmlayer of still air. Express both answers in SI units.

(b) In the United States, Rvalues of building materials are normally given in English units,Fft2hr/Btu. A Btu, or British thermal unit, is the energy needed to raise the temperature of a pound of water 1F. Work out the conversion factor between the SI and English units for values. Convert your answers from part (a) to English units.

(c) Prove that for a compound layer of two different materials sandwiched together (such as air and glass, or brick and wood), the effective total Rvalue is the sum of the individual Rvalues.

(d) Calculate the effective Rvalue of a single piece of plate glass with a 1.0mmlayer of still air on each side. (The effective thickness of the air layer will depend on how much wind is blowing; 1mmis of the right order of magnitude under most conditions.) Using this effective Rvalue, make a revised estimate of the heat loss through a 1m2single-pane window when the temperature in the room is 20Chigher than the outdoor temperature.

During a hailstorm, hailstones with an average mass of 2g and a speed of 15 m/s strike a window pane at a 45o angle. The area of the window is 0.5 m2 and the hailstones hit it at a rate of 30 per second. What average pressure do they exert on the window? How does this compare to the pressure of the atmosphere?


In analogy with the thermal conductivity, derive an approximate formula for the diffusion coefficient of an ideal gas in terms of the mean free path and the average thermal speed. Evaluate your formula numerically for air at room temperature and atmospheric pressure, and compare to the experimental value quoted in the text. How does D depend on T, at fixed pressure?

An ideal gas is made to undergo the cyclic process shown in the given figure. For each of the steps A, B, and C, determine whether each of the following is positive, negative, or zero: (a) the work done on the gas; (b) the change in the energy content of the gas; (c) the heat added to the gas.

Then determine the sign of each of these three quantities for the whole cycle. What does this process accomplish?

The enthalpy of combustion of a gallon (3.8 liters) of gasoline is about 31,000kcal. The enthalpy of combustion of an ounce28g of corn flakes is about100kcal. Compare the cost of gasoline to the cost of corn flakes, per calorie.

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free