(a) What is the unknownemfxin a potentiometer that balances whenRxis 10.0Ω , and balances when role="math" localid="1656393398590" Rsis 15.0Ωfor a standard 3.000-V emf? (b) The sameemfxis placed in the same potentiometer, which now balances when Rsis 15.0Ω for a standard emf of 3.100-V . At what resistanceRxwill the potentiometer balance?

Short Answer

Expert verified

The unknown emf of the potentiometer is Ex=2V.

(b) The unknown resistance for the potentiometer is Rx=9.7Ω.

Step by step solution

01

Concept Introduction

The rate of electron flow can be described as the aggregate flow of electrons via a wire. The term "resistance" refers to anything that stands in the way of current flow. To convert electrical energy to light, heat, or movement, an electrical circuit must have resistance.

The electric potential generated by an electrochemical cell or a changing magnetic field is known as electromotive force. Electromotive force (EMF) is a well-known abbreviation.

02

Emf in a potentiometer(a)

Calculate the emf Exin a potentiometer that balances when Rx=10Ωand Rs=15Ω for standard emf Es=3V. Now, it can be calculated -

role="math" localid="1656395116969" Ex=EsRxRs=(3V)10Ω15Ω=2V

Therefore, the emf value is obtained as Ex=2V.

03

Resistance in a potentiometer(b)

Connect the same emf Ex, in a potentiometer that balances when Rs=15Ωfor standard emf . The resistance is then,

Ex=EsExEs=(15Ω)2V3.1V=9.7Ω

Therefore, the value for resistance is Rx=9.7Ω.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

If you wish to take a picture of a bullet traveling at 500 m/s , then a very brief flash of light produced by an discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RCconstant is acceptable, and given that the flash is driven by a 600-mFcapacitor, what is the resistance in the flash tube?

An ECG monitor must have an \(RC\) time constant less than \(1.00 \times {10^2}{\rm{ }}\mu s\) to be able to measure variations in voltage over small time intervals. (a) If the resistance of the circuit (due mostly to that of the patient’s chest) is\(1.00{\rm{ }}k\Omega \), what is the maximum capacitance of the circuit? (b) Would it be difficult in practice to limit the capacitance to less than the value found in (a)?

Consider the circuit in Figure21.53, and suppose that the emfs are unknown and the currents are given to beI1=5.00A,I2=3.0A,andI3=-2.00A. (a) Could you find the emfs? (b) What is wrong with the assumptions?

A student in a physics lab mistakenly wired a light bulb, battery, and switch as shown in Figure 21.44. Explain why the bulb is on when the switch is open, and off when the switch is closed. (Do not try this—it is hard on the battery!)

Suppose you are using a multimeter (one designed to measure a range of voltages, currents, and resistances) to measure current in a circuit and you inadvertently leave it in a voltmeter mode. What effect will the meter have on the circuit? What would happen if you were measuring voltage but accidentally put the meter in the ammeter mode?

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free