A large research solenoid has a self-inductance of 25.0 H (a) What induced emf opposes shutting it off when 100 Aof current through it is switched off in 80.0ms? (b) How much energy is stored in the inductor at full current? (c) At what rate in watts must energy be dissipated to switch the current off in 80.0ms? (d) In view of the answer to the last part, is it surprising that shutting it down this quickly is difficult?

Short Answer

Expert verified

a. The induced electromotive force is 31.25 kV .

b. The energy stored in the inductor is 1.25×105J.

c. The power released will be 1.56 MW .

d. No, it is not difficult to switch it off.

Step by step solution

01

Given Data

The self-inductance of the solenoid is M=25.0 H

The time interval when the current is switched off is t=80.0ms10-3s1ms=0.08s

The change in the current is,l=100A

02

Concept Introduction

An inductor is a passive electrical component that counteracts current fluctuations. Coils and chokes are other names for inductors. An inductor is represented by the letter L in electrical notation.

03

Finding the induced electromotive force(a)

The induced electromotive force can be expressed as,

ε=-Mlt……………..(1)

Where M is self-inductance and lis the change in the current in the time interval t.

Substituting the given data in equation (1), we get,

ε=-25.0H100A0.08s=-31250V1kV1000V=-31.25kV

Therefore, the induced electromotive force is-31.25kV

04

Finding energy stored in the inductor(b)

When current runs through an inductor with inductivity M , the energy stored in it can be determined using the expression,

E=MI22………………(2)

Substituting the given data in equation (2) gives,

E=25.0H×100A22=1.25×105J

Therefore, the stored energy is1.25×105J

05

Finding the power released(c)

If this energy is consistently released over a set of time, the power released can be expressed as,

P=Et………………(3)

Substitute the given data in equation (3), and we get,

P=1.25×105J0.08s=1.56×106W1MW106W=1.56MW

Therefore, the power released is1.56MW

06

Explanation(d)

Given the inductor's enormous power, it's not unexpected that turning it down rapidly is difficult.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

A motor operating on 240 V electricity has a 180 V back emf at operating speed and draws a 12.0 A current. (a) What is its resistance? (b) What current does it draw when it is first started?

A cassette recorder uses a plug-in transformer to convert\(120{\rm{ }}V\)to\(12.0{\rm{ }}V\), with a maximum current output of\(200mA\).

(a) What is the current input?

(b) What is the power input?

(c) Is this amount of power reasonable for a small appliance?

(a) Calculate the self-inductance of a \({\rm{50}}{\rm{.0}}\)cm long, \({\rm{10}}{\rm{.0}}\)cm diameter solenoid having \({\rm{1000}}\) loops. (b) How much energy is stored in this inductor when \({\rm{20}}{\rm{.0}}\) A of current flows through it? (c) How fast can it be turned off if the induced emf cannot exceed \({\rm{3}}{\rm{.00}}\)V?

(a) An inductor designed to filter high-frequency noise from power supplied to a personal computer is placed in series with the computer. What minimum inductance should it have to produce a\(2.00{\rm{ }}k\Omega \)reactance for\(15.0{\rm{ }}kHz\)noise? (b) What is its reactance at\(60.0{\rm{ }}Hz\)?

Derive an expression for the current in a system like that in figure below, under the following conditions. The resistance between the rails is R , the rails and the moving rod are identical in cross section A and have the same resistivity ρ. The distance between the rails is l, and the rod moves at constant speed v perpendicular to the uniform field B. At time zero, the moving rod is next to the resistance R.

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free