Figure 12-50 shows a 70kgclimber hanging by only the crimp holdof one hand on the edge of a shallow horizontal ledge in a rock wall. (The fingers are pressed down to gain purchase.) Her feet touch the rock wall at distanceH=2.0mdirectly below her crimped fingers but do not provide any support. Her center of mass is distance a=0.20mfrom the wall. Assume that the force from the ledge supporting her fingers is equally shared by the four fingers. What are the values of the(a) horizontal component Fhand (b) vertical component Fvof the force on eachfingertip?

Short Answer

Expert verified

a) The horizontal force component of force is17N .

b) The vertical force component of force is 170N.

Step by step solution

01

Listing the given quantities

The mass of climber is,m=70kg.

The climber touches the rock wall at a distance,H=2m.

The center of mass is at,a=0.20m .

02

Understanding the concept of component resolve

We can write the equation of the horizontal component of forces. We can then write the torque equation at point O. using these two equations, we can get the horizontal component of force. To find the vertical force component, use the vertical force equilibrium condition.

03

Free Body Diagram

Free Body Diagram:

04

(a) Calculations of the horizontal force component

Using equilibrium condition, the net force in x direction can be written as,

Fx=0

Substitute the values in the above expression, and we get,

Fy=0

(1)

Using equilibrium condition, the net force in y- direction can be written as,

Fy=0

Substitute the values in the above expression, and we get,

4Fvmg=0

(2)

Torque at point acan be calculated as,

mga(4Fh)H=0Fh=mga4H

Substitute the values in the above expression, and we get,

Fh=70 kg×9.8 m/s2×0.2 m4×2.0 m=17.16(1 kgm/s2×1 m1 m×1N1 kgm/s2)=17N

Thus, the horizontal force component of force is17N .

05

(b) Calculations of the vertical force component 

From equation 2, we can write,

Fv=mg/4

Substitute the values in the above expression, and we get,

Fv=70 kg×9.8 m/s24=171.675(1 kgm/s2×1N1 kgm/s2)~170N

Thus, the vertical force component of force is170N170N.

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

In Figure 12-43, a climber leans out against a vertical ice wall that has negligible friction. Distance ais 0.914 m and distance Lis2.10 m. His center of mass is distance d=0.940 mfrom the feet–ground contact point. If he is on the verge of sliding, what is the coefficient of static friction between feet and ground?

A door has a height of 2.1 m along a yaxis that extends vertically upward and a width of 0.91 malong an xaxis that extends outward from the hinged edge of the door. A hinge 0.30 m from the top and a hinge 0.30 m from the bottom each support half the door’s mass, which is27 kg . In unit-vector notation, (a) what is the forces on the door at the top hinge and (b) what is the forces on the door at the bottom hinge?

In Fig. 12-76, a uniform rod of mass m is hinged to a building at its lower end, while its upper end is held in place by a rope attached to the wall. If angleθ1=60°, what value must angleθ2 have so that the tension in the rope is equal to mg/2?

A solid copper cube has an edge length of 85.5cm. How much stress must be applied to the cube to reduce the edge length to85.0cm ? The bulk modulus of copper is1.4×1011N/m2 .

Figure 12-85ashows details of a finger in the crimp holdof the climber in Fig. 12-50. A tendon that runs from muscles inthe forearm is attached to the far bone in the finger. Along the way, the tendon runs through several guiding sheaths called pulleys. The A2 pulley is attached to the first finger bone; the A4 pulley is attached to the second finger bone. To pull the finger toward the palm, the forearm muscles pull the tendon through the pulleys, much like strings on a marionette can be pulled to move parts of the marionette. Figure 12-85bis a simplified diagram of the second finger bone, which has length d. The tendon’s pull Fton the bone acts at the point where the tendon enters the A4 pulley, at distance d/3 along the bone. If the force components on each of the four crimped fingers in Fig. 12-50 are Fh=13.4 Nand Fv=162.4 N, what is the magnitude ofFt ? The result is probably tolerable, but if the climber hangs by only one or two fingers, the A2 and A4 pulleys can be ruptured, a common ailment among rock climbers.

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free