In Fig. 6-62, a 5.0 kgblock is sent sliding up a plane inclined at θ=37°while a horizontal force of magnitude 50 Nacts on it. The coefficient of kinetic friction between block and plane is0.30. What are the (a) magnitude and (b) direction (up or down the plane) of the block’s acceleration? The block’s initial speed is 4.0 m/s. (c) How far up the plane does the block go? (d) When it reaches its highest point, does it remain at rest or slide back down the plane?

Short Answer

Expert verified

(a)a=+2.1m/s2

(b) Down the plane.

(c) 3.9 m

(d) Remains at rest

Step by step solution

01

Given

M=5.0kg,θ=37°F=50N,μk=0.30

02

Understanding the concept

Frictional force is given by the product of coefficient of friction and the normal reaction. Newton’s 2nd law states that the acceleration of an object as produced by a net force is directly proportional to the magnitude of the net force, in the same direction as the net force, and inversely proportional to the object’s mass. Using these concepts, the problem can be solved.

Formula:

fk=μkFkF=ma

03

Calculation for magnitude of the block’s acceleration

(a)

Applying Newton’s second law to the x (directed uphill) and y (directed away from the incline surface) axes, we obtain

Fcosθ-fk-mgsinθ=maFN-fsinθ-mgcosθ=ma

Using. fk=μkFN

a=Fmcosθ-μksinθ-gsinθ-μkcosθ=50N5.0kgcos37°-0.37sin37°-gcos37°+0.37sin37°a=-2.1m/s2ora=+2.1m/s2

04

Calculation for the direction of the block’s acceleration 

‘(b)

The assumed direction for acceleration in part (a) is up the inclined plane and after the calculation it camea=-2.1m/s2 . This negative shows our assume direction is wrong. So, the direction of is down the plane.

05

Calculate how far up the plane does the block go

(c)

v0=+4.0m/sand v = 0,

x=v2-v022a=4m/s2-02-2.1m/s2=3.9m

06

Find out if the block remains at rest or slides back down the plane when it reaches its highest point

(d)

we expectμsμk ; otherwise, an object started into motion would immediately start decelerating (before it gained any speed)!

fs,max=μsFN=μSFsinθ+mgcosθ

Which turns out to be 21 N. But acceleration along the x axis is zero, we must have

fs=Fcosθ-mgsinθ=10N

(The fact that this is positive reinforces our suspicion thatfs points downhill).

Since thefs needed to remain at rest is less thanfs,max then it stays at that location

Unlock Step-by-Step Solutions & Ace Your Exams!

  • Full Textbook Solutions

    Get detailed explanations and key concepts

  • Unlimited Al creation

    Al flashcards, explanations, exams and more...

  • Ads-free access

    To over 500 millions flashcards

  • Money-back guarantee

    We refund you if you fail your exam.

Over 30 million students worldwide already upgrade their learning with Vaia!

One App. One Place for Learning.

All the tools & learning materials you need for study success - in one app.

Get started for free

Most popular questions from this chapter

Anblock of steel is at rest on a horizontal table. The coefficient of static friction between block and table is 0.52. (a) What is the magnitude of the horizontal force that will put the block on the verge of moving? (b) What is the magnitude of a force acting upward60°from the horizontal that will put the block on the verge of moving? (c) If the force acts downward at60°from the horizontal, how large can its magnitude be without causing the block to move?

A police officer in hot pursuit drives her car through a circular turn of radius 300mwith a constant speed of 80.0km/h. Her mass is55.0kg. What are (a) the magnitude and (b) the angle (relative to vertical) of the net force of the officer on the car seat? (Hint: Consider both horizontal and vertical forces)

In Fig. 6-54, the coefficient of kinetic friction between the block and inclined plane is 0.20, and angle θis 60°. What are the

(a) magnitude aand

(b) direction (up or down the plane) of the block’s acceleration if the block is sliding down the plane?

What are (c) aand (d) the direction if the block is sent sliding up the plane?

A block is pushed across a floor by a constant force that is applied at downward angle θ(Fig. 6-19). Figure 6-36 gives the acceleration magnitude a versus a range of values for the coefficient of kinetic friction μkbetween block and floor: a1=3.0m/s, μk2=0.20, μk3=0.40.What is the value of θ?

A house is built on the top of a hill with a nearby slope at angleθ=45°(Fig. 6-55). An engineering study indicates that the slope angle should be reduced because the top layers of soil along the slope might slip past the lower layers. If the coefficient of static friction between two such layers is 0.5, what is the least angle ϕthrough which the present slope should be reduced to prevent slippage?

See all solutions

Recommended explanations on Physics Textbooks

View all explanations

What do you think about this solution?

We value your feedback to improve our textbook solutions.

Study anywhere. Anytime. Across all devices.

Sign-up for free